Gam METAL HALIDE 575W User Manual download pdf

Page 1 of 4

www.rosco.com

GAM Product # GL4002.15/30,25/50

METAL HALIDE 575W

PRODUCT INSTRUCTIONS

Congratulations on using one of the most powerful

METAL HALIDE 575W proﬁle ﬁxtures in the word. The

following information will guide you through the setup

process and operation of the GAM METAL HALIDE

575W with the electronic ballast LI4000.01M

The GAM METAL HALIDE 575W is for professional use

only. Read this complete manual before you start using.

Do not open the cover as this will cancel the warranty.

Unpacking and Powering:

Before connecting the ballast to A/C, ﬁrst assemble; (1)

The A/C connection on the ballast, (2) the DMX connec-

tions, (3) the head cable connection between the ballast

and the GAM 575W METAL HALIDE ﬁxture. (4) Now

install the lamp.

A/C Connection:

Requires direct 90-265VAC, 50/60Hz power.

DO NOT PLUG THE ELECTRONIC BALLAST INTO A

THEATRICAL DIMMER CIRCUIT, EVEN IF IT IS PROFILED

IN THE LIGHTING CONTROL BOARD AS NON-DIM.

There is an A/C cable provided which plugs into the ICE

male connector on the ballast. There is an additional ICE

female connector to power the INNO DIM (Lighting In-

novations Dimmer Shutter). Please consider the maximum

output current (7A at 230VAC, 4A at 110VAC).

DMX-Connection:

DMX input is connected to the built-in XLR5 male

connector. Additional DMX units are connected to DMX

throughout. The last unit in the DMX chain must have a

termination (120Ω resistor between pin 2 and pin 3). It

is recommended that if the GAM METAL HALIDE 575W

is being used with an INNO DIM, then the DMX chain

ﬁrst runs to the GAM METAL HALIDE 575W ballast and

then is terminated at INNO DIM. There is a built-in DMX

termination switch on the INNO DIM, which then can

be turned to “on”.

CAUTION

When using a DMX device with a discharge lamp such

as CDM or an HMI, it’s suggested that you separate the

power circuit for the discharge lamp from the DMX control

device. When using DMX controlled units such as an In-

dexing TwinSpin™ or SX4® Gobo Changer or DMX Loop

Tray, the “noise” from the discharge lamp ballast may

cause some interference and or damage the electronics.

For best results we recommend providing separate line

voltage to the DMX devices and the discharge light ﬁxture.

Electronic Ballast #LI4000.01M

1 2 3 4

METAL HALIDE 575W 1

Summary of Contents

Page 1 - METAL HALIDE 575W

Page 1 of 4www.rosco.comGAM Product # GL4002.15/30,25/50METAL HALIDE 575WPRODUCT INSTRUCTIONSCongratulations on using one of the most powerful METAL

Page 2

Silicone cable connection between ballast & ﬁxture:Connect the Amphenol plug coming from the lamphouse to socket (output to lamp). Screw on the ba

Page 3

Page 3 of 4www.rosco.comGAM Product # GL4002.15/30,25/50METAL HALIDE 575WLocal OperationSet the switch to manual operation. You can switch the lamp on

Page 4

Page 4 of 4www.rosco.comGAM Product # GL4002.15/30,25/50METAL HALIDE 575WFuses10A, 5x20mm, slow blowDisconnect ballast & ﬁxture from power. Use a

Comments to this Manuals

No comments

Gam METAL HALIDE 575W User Manual

Browse online or download User Manual for Lighting Gam METAL HALIDE 575W. GAM METAL HALIDE 575W User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Lighting Gam METAL HALIDE 575W